Colors: Red 1201-1, Light Blue 1202-1, Black 1205-1, Dark Blue 1230-1, Grey 1231-1, Green 1234-1, Teal 1235-1
Finish/Sheen: Semi-Gloss
Biocide Content: 4.5%
Copper Content: 42% (all Colors)
Volume Solids: 62% +- 2%
Solids by Weight: 85
Shipping Weight: 17-18 Lbs./Gal.
Flash Point: 100° F
VOC: 288 Grams/Liter
Typical Film Thickness:
Pleasure Craft: 3.0 mils dry film thickness (DFT) per coat, (5.0 mils wet film thickness (WFT))
Commercial Marine: 4.0-5.0 mils DFT per coat by spray application (7.0- 8.0 Mils WFT)
Recommended Coats: 2 heavy coats on entire hull and 3 at waterline and other high wear areas
Theoretical Coverage: 331 Sq.Ft./Gal. @ 3.0 mils DFT

Application Controls 

Method: This product may be applied by airless and conventional spray, solvent resistant rollers and brushes.

Surface Preparation

Paint only clean, dry surfaces. Remove all grease, oil, wax, or other foreign material by solvent or detergent washing. (SSPC-SPI)

Compatibility: For pleasure craft applications, please refer to our Sea Hawk Compatibility Chart to ensure compatibility when applying Biocop TF antifouling paint over existing bottom paint.

Previously Painted Surfaces: Seahawk Biocop TF is suitable for this substrate. For correct procedures please refer to the Application Guidelines for Fiberglass/Gelcoat.

Fiberglass or Vinyl Ester Hulls: Sea Hawk Biocop TF is suitable for this substrate. For correct procedures please refer to the Application Guidelines for Fiberglass/Gelcoat.

Wood Surfaces: New Work - Sand the wood surface with 80 grit sandpaper, remove the sanding dust with Sea Hawk S-90 Cleaner, allow to dry and apply the first coat of Sea Hawk Biocop TF bottom paint. Reduce the first coat (only) 20% with Sea Hawk 2033 Thinner to maximize surface penetration. Next, apply whatever seam compound if needed, allow to dry in accordance with the product label and apply two more coats of Biocop TF without any Thinner reduction. 

Aluminum: Biocop TF Antifouling paint may be used on an aluminum hull only when used with the proper barrier coat system described in Technical Bulletin AL1284. Sea Hawk Biocop TF is not to be used on bare aluminum.

Steel Vessels: Sea Hawk Biocop TF antifouling paint is normally used as part of a paint system for underwater hull areas on steel vessels. Nominally, Biocop TF is applied over a properly cleaned existing surface of another antifouling paint or sealer. The surface must be clean and dry prior to application, free of all surface contamination. We highly recommend the hull bottom be high pressure water washed immediately upon haul out with 2,500-3,000 psi clean fresh water. Some areas may need to be cleaned in accordance with SSPC-SP-1 Solvent Cleaning to ensure all oils, grease, and other contaminants are removed. Please refer to additional data below and the section on recommended systems for steel below.

Additional Data For Painting Steel Hulls: If the surface to be painted is also to be repaired with an epoxy primer system, we recommend the area first be grit blasted to SSPC-SP-10 ‘near white metal', cleaned free of dust and blast media and primed in accordance with the primer system specifications. Please refer to the specified primer data sheet for application details. Make sure the first coat is applied within the proper over coating window of the last coat of epoxy primer which is normally while the epoxy is still tacky but cannot be removed with the thumb. Apply at least two coats of Sea Hawk Biocopt TF antifoulant for best performance.