Monthly Archives: January 2014

Awlgrip vs. Awlcraft 2000 – What are the differences?

Awlgrip and Awlcraft 2000 – Which is better?

Here’s an overview of the key differences between Awlgrip and Awlcraft 2000, (each one has its own advantages and disadvantages), so you can make an informed decision about which is right for you.

KEY TAKEAWAY

1. Awlgrip provides superior gloss, color consistency, and durability due to its two-component urethane formula.
2. Awlcraft 2000 offers a single component water-based formula that’s easier to apply and can be buffed and polished for improved shine retention.
3. Awlgrip is more expensive than Awlcraft 2000 but provides better protection against UV rays, chemicals and abrasion over time.
4. Awlcraft 2000 requires less prep work compared to traditional, solvent based topcoats like Awlgrip, making it easier and faster to apply with minimal odor or cleanup needed afterwards.
5. Both products provide excellent resistance to fading, chalking, weathering, and corrosion when applied properly in the right environment.

Awlgip Marine PaintsAwlgrip is based on a polyester urethane resin and Awlcraft 2000 is based on an Acrylic Urethane resin. At the surface they seem very similar, but at the molecular level they are vastly different. Polyester molecules are much smaller than acrylic molecules. This means that at any given volume, there can be more polyester molecules than acrylic and this allows polyester films to be more dense and tough. Awlgrip has more abrasion and chemical resistance than Awlcraft and is usually more rigid.

Awlcraft, on the other hand is not without its own advantages.  It is generally easier to apply. The larger molecules and less dense film of the acrylic allows for faster drying and therefore less dust entrapment in the finish.  Both urethane topcoats will resist staining and provide a long lasting gloss. It is best to consider cure times, reparability, application methods, chemical resistance, as well as abrasion resistance when deciding which topcoat to choose.

Which is more suited for buffing?

Both Awlgrip and Awlcraft 2000 urethane topcoats have a protective resin layer. This layer is the first line of defense against UV light and abrasive damage. Underneath this resin is a layer of rich pigment particles that give the paint its bright shine and color. Awlgrip has a thicker protective resin layer and when the polyester is scratched, it is necessary to cut deeply into the resin to repair it. Buffing the surface leaves the pigment exposed and compromises the performance of the paint in the long run.

Awlcraft has a softer finish, due to the less dense molecular structure, and thus has a lower melting point. When this acrylic urethane is buffed, the resin is able to flow together and does not require cutting the surface as deeply. So, Awlcraft 2000 is more suited for buffing and Awlgrip will require a Fairing Compound.

Awlgrip vs Awlcraft 2000 – Fast Facts

Awlgrip Polyester Urethane Topcoat

  • Can be applied by spray or brush/roll.
  • Excellent color retention and chemical resistance.
  • More dense molecular structure.

Awlcraft 2000 – Acrylic Urethane Topcoat

  • For spray application only.
  • Superior flow-out and high gloss.
  • Fast drying to reduce dust entrapment.
  • More user friendly in application. Easy to repair.

Awlgrip Color Chart

 

Restoring and Maintaining Awlgrip and Awlcraft 2000 Paint

Over time contaminants can build up and cause the finish of your Awlgrip/Awlcraft 2000 paint to appear dull.  You can restore the gloss of a freshly painted boat and prevent the premature aging caused by contaminates by following these steps:

  • Wash your Awlgrip or Awlcraft surface with Awlwash mixed with water (1-2 capfuls in a bucket of water for washing) using soft, non-abrasive cloths and rinse well. Doing so on a regular basis (once per month) will help control dulling buildup.
  • Solvent cleaning of Awlgrip only: Awlprep and Awlprep Plus can be used to aid in removal of stains or markers and to soften or remove heavy build ups of grease and grime, or spray paint on the topcoat and toluene, lacquer thinner, M.E.K., acetone can be used as well.
  • Solvent cleaning of Awlcraft 2000 and Awlgrip HDT only: Awlprep or mild solvents (mineral spirits, xylene, kerosene and diesel fuel) should be used.

Awlgrip AWLwashIn both cases apply solvents with soft cloths and do not allow the chemicals to dry on surface, puddle or soak. Wash with Awlwash to prevent remaining solvent to attack paint. As always when working with solvents, test in an inconspicuous area first.

 Distilled white vinegar and hot water will aid in removing salt stains, always follow with Awlwash.

Protecting the Surface

awlgrip awlcareAwlcare can be applied to the surface like a wax to remove pollutants (such as diesel soot), protects the finish and leaves a glossy shine. Awlcare should be applied regularly to protect against pollutants. It can be removed with Awl-Prep Plus (Awlgrip only) when it’s time to repaint. What to avoid with Awlgrip and Awlcraft 2000:

  • Abrasives
  • Polishing compounds
  • Traditional waxes as they tend to break down rapidly, yellow and attract dirt
  • Acid based products such as teak or metal cleaners and strong solvents on Awlcraft 2000, Awlbrite Clear or Awlspar Varnish.
  • Trapped moisture from supplies as paint can blister or delaminate

AVOID:

  • Avoid Traditional Waxes
  • Awlgrip topcoat only: Regular applications of Awlcare will help temporarily seal and restore shine to painted surfaces that have become porous due to age or mistreatment, helping to maintain a satisfactory appearance until there is time to repaint.
  • Awlcraft 2000 and Awlgrip HDT: Awlcare Protective Polymer Sealer will help maintain the gloss on these finishes with regular applications, especially those which have been buffed or polished. Remember, Awlcare is only applied and buffed by hand. Never apply or buff Awlcare with a machine.
  • Avoid abrasive and polishing compounds
  • Avoid strong solvents (eg. lacquer thinner, M.E.K., acetone) to clean Awlcraft 2000, Awlgrip HDT, Awlbrite Clear or Awlspar varnish.