This application instruction sheet has been prepared for use with all Lifeguard Pool Paint products on properly prepared surfaces. Please read this document in its entirety before proceeding. Never apply below 50F, above 85F, in hot direct sunlight, when humidity is above 75%
or when rain is forecast within 48 hours. Most applications are by
roller-coat, however brush and spray applications are acceptable.
Recommend applying one coat of primer with two coats of pool paint. We
recommend using 3/8” nonshedding roller cover on smooth surfaces, use
higher nap covers on rough surfaces. When using over previously applied
paint we recommend doing a test area before committing to the entire
project to prevent potential compatibility issues.
New concrete, plaster and masonry and similar surfaces should be allowed
to cure a minimum of thirty days before application. The maximum level
of hydrostatic pressure is 4.0 LBS. To avoid vapor transmission or
hydrostatic pressure resulting in adhesion issues or blistering we
recommend establishing the actual level of hydrostatic pressure by
utilizing the VaporGuage Calcium Chloride moisture test, or its
equivalent. Where hydrostatic pressure is found to be unacceptably high
we recommend using LG-104 Seal-it! Deep Penetrating Sealer according to
label directions. Once treated with Seal-it! retest to confirm
acceptable levels of hydrostatic pressure have been achieved before
All applications will require the removal of all grease, oil, contaminates, sanding residue and the use of LG-695 Etching Cleaner,
muriatic acid or the equivalent according to industry standards. For
best results we recommend removing existing paint, coatings or sealers.
The recoat window is typically 12-48 hours, sand between coats after 48
hours. All recommendations, written and verbal advice, these directions,
label instructions and standard industry practices must be strictly
adhered to or Limited Warranty is voided. Refer there for specific
information about Seal-it! Deep Penetrating Sealer and VaporGauge Moisture Test Kits.
Preparation. Begin by draining the pool or pond, removing all loose debris. When preexisting paint is
present your first step should be to establish how many coats of paint
are present. The best way to do that is to remove a chunk of the old
coating with a knife blade and
count the layers of old paint. When four or more layers of old paint are
present stripping is the industry standard, thus required. We recommend
using LG-646 Triple Strength Paint Stripper which is available on your
website. Schedule your project carefully. All surfaces to be repaired or
painted must be allowed to dry thoroughly before application. Be sure
moisture and hydrostatic pressure is at acceptable levels before moving
forward. As necessary tape off the tile band, lights and fittings with
masking tape to prevent unwanted paint on lights, threads, tile or
fittings. Check the weather
report carefully for rain, high humidity or high winds. When there is a
chance of rain or high humidity within 48 hours, you will want to wait
until the forecast allows sufficient low humidity, clear, dry warm
weather to prime or paint. Do not apply repair material, primer or paint
to wet surfaces. Our product performance guaranty and Limited Warranty
are voided when Life Guard Pool Paint Products are applied to wet
surfaces and when rain, high humidity or vapor transmission corrupt the
Make your repairs. Begin by power-washing all pool surfaces thoroughly. Inspect the entire surface carefully to locate areas in need of repair. Tap the surface with a ball
peen hammer at regular intervals. When tapped with a hammer unsound
areas will sound different than sound areas. Mark any unsound areas with
a marking pen for easy identification. All repairs should be
completed and allowed to cure prior to sanding, blasting, grinding or
application. Sanding, grinding or blasting is beneficial but often not
required where circumstances and conditions permit, you must be the
judge, consider carefully before proceeding. When selecting your repair
materials be sure to choose submersible and paintable calking, fillers
and patching materials. When cracks are present they must be cut
out with a diamond blade saw or grinder. Cut or grind the cracks out a
minimum of 1/4” deep and ¼” wide. Chip out any divots or loose cement.
Fill or caulk the cracks and divots. Larger repairs should be filled
with hydraulic cement according to manufacturer’s directions. Recommend
sanding the entire surface to be painted with 150 grit sandpaper, or
blasting. Clean up all loose debris and rinse before moving forward.
Clean / Seal. LG-695 Etching Cleaner Concentrate achieves
results equal to muriatic acid however it is considerably easer to use, safer in the drains and flower beds. It removes leaching lime, contaminates, grease, oil and corrects the Ph, opening the pores improving adhesion. Some recommend TSP (Tri Sodium Phosphate), however, its use alone is insufficient in our opinion. Apply LG-695 Etching Cleaner Concentrate according to label directions and rinse thoroughly. Repeat this step when evidence of stubborn oil, stains or wax is evident. Rinse the entire pool, skimmers, fittings, lights, and stairs completely. Where there is evidence (or the suspicion) of vapor emission or hydrostatic pressure we
recommend using LG-104 Seal-It! Deep Penetrating Sealer to permanently seal the substrate.
Select the right primer and sundries. For best results apply one
coat of the recommended Life Guard Primer. We recommend priming bare
concrete, plaster and steel, with either LG-664 Etching Primer, LG-715 Chloro-Prime or TS-6390 Ever-Last Epoxy Primer. Prime aluminum, fiberglass, plastic, vinyl, plaster and Gunnite surfaces with LG-664 Etching Primer.
IMPORTATNT NOTE: LG-664 Etching Primer is porous. It can pick up
atmospheric moisture or moisture within the substrate. Extra care must be taken to be sure it is thoroughly dry at time of application or paint
may fail to properly adhere to it! We do not recommend LG-664 Etching
Primer on porous substrates.
Applying Primer. Carefully schedule your primer and paint. Do not
apply primer when the temperature is below 50F, above 85F or when
humidity will be above 75% or in hot direct sunlight. Stir thoroughly
before application. Dilute with recommended thinner only as needed. We
recommend 3/8” non-shedding roller covers for smooth surfaces, increase
roller nap as on more heavily textured surfaces. Apply primer evenly
avoiding heavy build up. Recommend Hand brushing the edges then rolling
the remaining areas. See label for recoat times. Typically only one
primer coat is required however multiple coats may be applied according
to individual requirements. Sanding between coats is not required when
recoated within 48 hours. Read and follow primer label directions
Applying Paint. Apply paint only after the dew has lifted, primer has thoroughly dried, and before the
temperature reaches 85F. Do not apply when the temperature is below 50F, above 85F, when humidity
will be above 75%, or when rain is in the forecast within 48 hours.
Dilute with recommended thinner only as needed. Stir again thoroughly.
Paint may be brushed, rolled or sprayed. Film build is better with roll
coat applications, which is usually preferable. Brush the edges,
fittings and hard to reach areas then roll coat the remaining area.
Apply evenly always keeping a wet edge which prevents lap marks. More
than one painter may be necessary to keep a wet edge in hot weather.
Apply evenly avoiding heavy build up. Apply subsequent coats within 48
hours or sand between coats. Actual dry, cure and re-coat times may be
extended depending on application method, application techniques
utilized, color and weather conditions.
Dry and Cure Time. Lifeguard Pool Paint Products must be allowed to dry and cure completely before
filling pool with water. Allow a minimum of 7 full days before filling your refinished pool. Allow additional
cure time for MT color (dark colors) and low temperatures. The first 48
hours is moisture critical! You must keep uncured paint dry for 48 hours
minimum. When unforeseen rain or moisture wets the painted
surface before the 7 day cure time, immediately remove standing water using a sponge or mop. Use a
leaf blower to dry the uncured painted surface. Add a minimum of two
days to the total cure time which will provide adequate time for curing
before filling. Fill the pool without stopping until the pool is full.
Restart the pool filtration system once the pool has been completely
filled. Adjust the total alkalinity and calcium hardness levels to a
minimum of 150 PPM. Resume your normal chemical maintenance program.
NOTE: Never apply Lifeguard Paint products on substrates exceeding 4 LBS hydrostatic pressure. Dry
and cures time vary with the weather, temperature, ventilation or
thickness of application. Allow extra dry and cure time for dark colors.
Protect your investment, blistering is typically the result of uncured
paint being contaminated by water!