Log In | My Account |    0 item(s), Total: $0
Advanced Search
Home ::  Fiberglass and Gel Coat Repair ::  Gel Coat Products and Additives ::  Partall Film #10 PVA Surfacing Agent For Gel Coat
Categories
 


Specials & Promos

Enter your email to receive exclusive discounts!

Information

Follow Us On

Bottom Paint Store is upfront


Bottom Paint Store Coupons on tjoos.com
 
 
Partall Film #10 PVA Surfacing Agent For Gel Coat
0 of 5 Stars
Partall Film #10 PVA Surfacing Agent For Gel Coat
 
Quantity:
Price: $39.99
 
 
Use this product as a surfacing agent when using Sea Hawk Gel Coat with wax additive .

Partall Film #10 is a polyvinyl alcohol (PVA) water/alcohol solution of water-soluble, film-forming materials. This parting film is particularly recommended as a parting agent for separation between polyester or epoxy resins and various mold surfaces. It is not recommended for use with resins containing water or giving off water during cure (i.e., phenolics) or with automotive finishes, as damage may occur.

Partall Film #10 will not shrink and pull away from corners or curved surfaces. After resin has dried, the film parts easily from the mold and is readily dissolved from the molded parts with water. An occasional coating of Partall Paste #2 is required on most mold surfaces before application of Partall Film #10.

May be applied over gel coat as a surface cure agent.

Application

Partall Film #10 is ready to use as received and should not be diluted. It is best applied to mold surface using a spray gun although it can be brushed on depending on desired post-production finish.

Best results are achieved with as fine a spray as possible. To achieve this result, use a small orifice in the gun, close the needle about halfway, and adjust the air pressure to 80 ƒ?? 100 psi at the gun (setting may vary depending on equipment used). Normal spraying distance is from 12 - 18 inches - Partall Film #10 should atomize prior to contact with mold surface.

Apply a thin mist coat first and allow to dry completely (approximately 10 - 15 minutes). Follow with two heavier flow coats, allowing each coat to dry completely before proceeding (approximately 30 - 45 minutes). A spray density that just allows the liquid to flow together and form a continuous film is ideal.

Dry film thickness must be at least 2 - 4 mils on new or reconditioned molds and 1 - 2 mils on seasoned molds (2 mils is the approximate thickness of an industrial-type trash bag). One gallon will cover about 400 square feet.

Drying time per coat is approximately 15 - 45 minutes (depending on thickness) with normal application. External factors such as humidity, proximity to sunlight, and the use of fans or heaters can cause drying time to vary. Film must be completely dry before proceeding with molding. Applying additional coats before a previous coat has dried thoroughly can compromise Partall Film #10's ability to adequately protect mold surface and prevent part from sticking. Film should be very smooth and glossy when dry - a dull film may result from insufficient spray and may contain pinholes.

Product Details
Manufacturer: No Manufacturer
Product SKU: 8155S/GL
 


 
 
 
 
We Also Recommend:

TR 104 Mold Release Wax 14oz Can
TR 104 Mold Release Wax 14oz Can 104 Wax 's primary use is specific for applications that need a release to maintain good properties when heat is a factor.
view more!
 
Customers who bought this product also purchased...

Table Top Epoxy Resin, 1 Gallon Kit
Table Top Epoxy Resin, 1 Gallon Kit
Always Free Shipping
Used extensively in coating surfaces and in table tops where a clear, hard and durable coating is required. Commonly seen on bar tops and restaurant t...
view more!
Marine Vinyl Ester Resin (GL) by Sea Hawk Paints
Marine Vinyl Ester Resin (GL) by Sea Hawk Paints In terms of physical properties and cost Sea Hawk Vinyl Ester Resin is a compromise between low-cost polyesters and epoxy resins. Its use is limited t...
view more!
Fiberglass Cloth Tape, 8 OZ, 50 Yard Roll
Fiberglass Cloth Tape, 8 OZ, 50 Yard Roll Fiberglass Cloth Tape, woven with non-raveling edge for glassing seams, chines, keels, bulkheads and inside/outside joints of rectangular shapes. Use ...
view more!
Fiberglass Cloth, 8 oz, 38 inches wide, 1 Yard
Fiberglass Cloth, 8 oz, 38 inches wide, 1 Yard Fiberglass Cloth 8 oz medium weight and strength cloth. Used commonly in boat building/repair applications. Good formability and easy wet out. Use wit...
view more!
Gel Coat Colors by Sea Hawk Paints
Gel Coat Colors by Sea Hawk Paints
Always Free Shipping
Gel Coat Colors: MatterhornWhite Flag Blue Ice Blue Teal ...
view more!
Fiberglass Chopped Strand Mat 1.5 OZ x 50" Wide
Fiberglass Chopped Strand Mat 1.5 OZ x 50 Fiberglass Mat also known as Chopped Strand Mat (CSM) is a non-woven material typically used for laminate build-up and repair work. Fiberglass Mat con...
view more!
 
 
 
 
Copyright © 2014 BottomPaintStore.com. All rights reserved.
About Us   |   Contact Us   |   Wholesale Account   |   Shipping   |   Industry Links   |   No Sales Tax   |  Terms and Conditions   |   Shopping Cart   |   Site Map