Sikkens Cetol Marine

Color: IVA300 Natural

Finish: Satin

Specific Gravity: 0.87

Volume Solids: 28.0%

Typical Shelf Life: 3 years

VOC (as supplied): 440 g/lt (average)

Mixing: Stir thoroughly before use.

Thinning: Do not thin.

Cleaner: Special Thinner 216.

Ventilation and Humidity Control: Ensure adequate ventilation during use.

Airless Spray: Not recommended.

Roller: Not recommended.

Other: Before applying any Cetol® products, prepare a 3 coat test sample on your wood to confirm desired colour results. To achieve optimal colour results always use the same Cetol® product initially applied when overcoating or applying maintenance coats.

Substrates: Suitable for use on all types of wood including oily timbers such as Teak.

Number of Coats: 2-3 as per spec

Coverage: (Theoretical) – 305.3 (ft²/Gal) - up to 400 (ft²/Gal) per coat. On new wood the coverage of the first coat will be lower as Cetol® Marine will penetrate the wood.

Application Method: Brush

Exposure to air and extremes of temperature should be avoided. For the full shelf life of Cetol® to be realised ensure that between use the container is firmly closed and the temperature is between 5°C/41°F and 35°C/95°F. Keep out of direct sunlight.

**IMPORTANT** If Cetol® Marine is spilled on gelcoat, remove immediately. Difficult stains may be removed from gelcoat with Interlux Fiberglass Solvent Wash 202. Do not allow excess Fiberglass Solvent Wash 202 to remain on gelcoat. For painted surfaces ONLY use Interlux Special Thinner 216. Do not allow excess Interlux Special Thinner 216 to remain on painted surfaces. Do not apply at temperatures within 3°C of dew point or in wet weather. Substrate temperature should be minimum 10°C/50°F and maximum 35°C/95°F. Ambient temperature should be minimum 15°C/59°F and maximum 35°C/95°F. Product temperature should be no less than 10°C/50°F and maximum 35°C/95°F. Avoid painting in direct sunlight.

Click this link to view Product Technical Data Sheet

Click this link to view Product SDS

PREPARATION

NEW EXTERIOR/INTERIOR WOOD: It is essential to remove any surface oils and contaminants prior to sanding and application of Cetol Marine. Sand surfaces with 180-220 (grade) grit paper (always sand along the length of the grain). Remove all sanding residue prior to application of Cetol® Marine. When working in interior or confined spaces always ensure there is proper ventilation. If the wood is exposed for more than 24 hours, clean the surface again in order to remove any contaminants.

EXTERIOR/INTERIOR -PREVIOUSLY COATED WOOD : Remove all coatings prior to application of Cetol® Marine. To remove old coating, either sand with 120-180 (grade) grit paper or use Interlux Interstrip 299E chemical stripper which has been designed for marine use. Once previous coating has been removed, follow instructions for New Exterior/Interior wood.

EXTERIOR-WEATHERED WOOD OR PREVIOUSLY OILED WOOD: To ensure good adhesion of Cetol® Marine on weathered or previously oiled wood, use Interlux Premium Teak Restorer with a nylon scruffing pad as per instructions on label. Rinse with fresh water and allow to dry. Once complete follow instructions for New Exterior/Interior wood.

METHOD

The wood moisture content should be below 18%. Apply liberally using a long-haired bristle brush, smoothly, in the direction of the grain. Keep a wet edge to prevent lap marks and thoroughly saturate end grains where possible. Apply 3 coats of Cetol® Marine. Always allow 24 hours drying time in between coats. Sanding between coats is not recommended as this will result in a reduction of dry film thickness. Recommended film thickness must be applied to ensure effective product performance.

Make regular inspections to all coated areas. Problem areas should be attended to immediately and maintenance coats should be routinely applied. If the coating is allowed to weather beyond the regular maintenance period of 1 year, returning this surface to excellent condition will be more difficult. Before application of a maintenance coat of Cetol® Marine, clean the surface to remove any surface contaminants. If blue fungi or mildew are present then they can be treated with Interlux Premium Teak Restorer with a nylon scruffing pad as per instructions on label. Rinse with fresh water and allow to dry. Sand lightly with 220-320 (grade) grit paper. Remove sanding residue prior to the application of Cetol® Marine.