Duralux Topside Marine Enamel, High Gloss, Gallon
- $57.88
- Availability:In Stock
- Brand: Duralux Marine Paints
- Product Code: DUR-7XXGL
PRODUCT DATA:
Available Colors: M720 White, M722 Black, M731 Haze Gray, M737 Cruiser Blue
Type: Alkyd Enamel
Sheen: High Gloss
Package Viscosity @ 77* F: 68-72 Kreb Units
Weight per Gallon (U.S.): 9.72
% Solids by Weight: 63%
% Solids by Volume: 46%
Recommended Dry Film Thickness: 1-1.5 Mils
Method of Application: Brush, Roller or Spray
Application Viscosity @ 77* F: 70 Kreb Units
Theoretical Spreading Rate @ 1Mil DFT: 400-500 square feet per Gallon
VOC: Maximum 3.8 # per Gallon
Dry Time: To touch - 4 hours, Recoat - overnight
Thinner/Cleaner: Naphtha
Reduction Ratio: None required, but if spraying use no more than 10 %
Flash Point: 100* F T.O.C.
Package Viscosity @ 77* F: 68-72 Kreb Units
Weight per Gallon (U.S.): 9.72
% Solids by Weight: 63%
% Solids by Volume: 46%
Recommended Dry Film Thickness: 1-1.5 Mils
Method of Application: Brush, Roller or Spray
Application Viscosity @ 77* F: 70 Kreb Units
Theoretical Spreading Rate @ 1Mil DFT: 400-500 square feet per Gallon
VOC: Maximum 3.8 # per Gallon
Dry Time: To touch - 4 hours, Recoat - overnight
Thinner/Cleaner: Naphtha
Reduction Ratio: None required, but if spraying use no more than 10 %
Flash Point: 100* F T.O.C.
SURFACE PREPARATION
All surfaces must be free of moisture, wax, dirt, rust, and other foreign matter. Remove any loose or peeling paint. Use sandpaper, power brushing, or a liquid de-glosser to dull any existing gloss. Remove all dust by wiping surfaces with a clean cloth dampened with paint thinner.
APPLICATION:
Unpainted Surfaces:
Fiberglass: Wipe down with Acetone prior to sanding and after sanding. Top with two full coats of Duralux Camouflage Paint.
Wood - Prime and apply two coats of Duralux Camouflage Paint.
Fiberglass: Wipe down with Acetone prior to sanding and after sanding. Top with two full coats of Duralux Camouflage Paint.
Wood - Prime and apply two coats of Duralux Camouflage Paint.
Steel: On clean, rust-free steel, apply two coats of Duralux Sub Trop Red Metal Primer M740 apply two coats of Camouflage Paint.
Aluminum: Pretreat with suitable wash primer, and apply two coats of primer. Top with two full coats of Duralux Camo Paint.
Painted Surfaces:
Fiberglass: Wipe down with Acetone prior to sanding and after sanding. Top with two full coats of Camouflage Paint.
Wood - Sand thoroughly, spot prime bare areas. Then apply two full coats of Duralux Camouflage Paint.
Fiberglass: Wipe down with Acetone prior to sanding and after sanding. Top with two full coats of Camouflage Paint.
Wood - Sand thoroughly, spot prime bare areas. Then apply two full coats of Duralux Camouflage Paint.
Steel: Clean all bare areas to bright steel. Touch up with two coats of Duralux Sub Trop Red Metal Primer M740. Top with two full coats of Duralux Camo Paint.
Aluminum: Touch up all bare areas with primer. Top with two full coats of Duralux Camouflage Paint.
METHOD OF APPLICATION
Brush, natural bristle.
Roller, short nap 1/4"-3/8" nap or mohair.
Spray: For airless spray use a .013" to .017" orifice with minimum 1,850 psi at tip. For conventional spray use Graco 700 Gun 217-757 equipment or equivalent, with fluid pressure of 20 lbs. and atomizing pressure of 35-40 lbs. Thinning: If thinning is desired, use Mineral Spirits or Xylene not to exceed a half pint (8 ounces) per gallon.
Thinning: Duralux is made for use as it comes from the can. If thinning is desired, Use no more than a one-half pint of Naptha per gallon. For spraying, use one-half pint to one pint per gallon.
Thinning: Duralux is made for use as it comes from the can. If thinning is desired, Use no more than a one-half pint of Naptha per gallon. For spraying, use one-half pint to one pint per gallon.
Coverage: On properly prepared surfaces, expect to cover from 400-500 square feet per. gallon.
Drying Time: Four hours, hut slightly longer on damp or cold days. Allow 12-16 hours for thorough hardening before repainting.
Clean Up: Immediately after use with mineral spirits or xylene.
How to Use: Apply two thin coats of DURALUX on properly prepared surfaces. "Feather edge" last brush strokes to insure a smooth finish. Do not over apply. Maintain a wet edge to avoid lap marks. Do not paint in direct sunlight.
Application Temperature, air, surface & material: Minimum 50°F, Maximum 100°F.
Relative Humidity: 85% maximum. At least 5°F above dew point.
A single package topside alkyd enamel for use on primed steel and metal, wood, aluminum, or fiberglass. Originally developed for pleasure and commercial boats, the properties of this marine enamel make it also ideal for onshore or offshore oilfield equipment, farm machinery, and plant maintenance operations. Duralux Marine Enamels withstand repeated washings, resist oil and gasoline, and hold up to the discoloration effects of harbor gases. Due to computer monitor color calibration differences, color swatches may not accurately represent the actual paint color.
Size: 1 Gallon.
See our Blue Water Mega Gloss for alternative color options.
Available Duralux Marine Paint Enamel Colors:
 |
 |
||||
|
|
|
|
|
|
|
 |
 |
||||
|
|
|
|
||
|
|
|
|
|
|
Review Summary
Duralux Topside Marine Enamel receives high praise for its ease of application, smooth finish, and durability, ensuring great results for marine projects.
This summary is AI-Generated
- Summary based on a representative sample of minimum 10 reviews with at least 20 characters
- This summary is updated weekly if the product has received at least 20% additional reviews.
Thanks for your feedback!
Was it helpful?
Yes
No
Related Products
