Interlux Trilux 33, Quart

 Color: YBA060-Blue, YBA061-Green, YBA063-Black, YBA068-White
Finish: Low sheen
Specific Gravity: 1.6
Volume Solids 50%
Typical Shelf Life: 2 yrs
VOC (As Supplied) 390 g/lt
1 US Gallon

Click here to view Interlux Trilux 33 Product Data Sheet

BARE ALUMINUM: Sand with medium grade (grit) emery cloth to a bright metal finish. Wipe clean. Apply one very thin coat of Viny-Lux Primewash 353/354. Prime with Interprotect 2000E/2001E. On sandblasted aluminum the Viny-Lux Primewash 353/354 can be omitted if priming with Interprotect the same day as blasting.
FACTORY FINISHED ALUMINUM: Prime with Primocon.
BARE FIBERGLASS: Begin by scrubbing well using soap and water and a stiff brush. Rinse with fresh water. Wipe a small area with a clean rag that has been wetted with Fiberglass Solvent Wash 202. While the surface is still wet, wipe with a clean, dry rag. Continue this process until the entire surface has been cleaned.

No Sand System - Apply one thin, continuous coat of Interlux Fiberglass No-Sand Primer.

Sanding System - Sand with 80 grade (grit) paper. Remove sanding residue. Wipe with Fiberglass Solvent Wash 202.
BARE WOOD: Sand with 80 grade (grit) paper. Clean with Special Thinner 216. Apply first coat reduced 10% with Special Thinner 216. Fill seams, if necessary, with Seam Compound Brown 30.
EPOXY COATED WOOD: Begin by scrubbing well using soap and water and a stiff brush. Rinse with fresh water. Sand with 120 to 180 grade (grit) paper. Remove sanding residue. Wipe with Fiberglass Solvent Wash 202. Prime with Interprotect 2000E/2001E.
PREVIOUSLY PAINTED SURFACES: with Trilux 33* or Trilux with Biolux Sand with 80 grade (grit) paper.
OTHER ANTIFOULINGS: Sand surface, wipe clean. Prime with Primocon. Remove antifouling paint in poor condition with Interstrip Semi-Paste 299E.

Method: At least 2 coats should be applied.
Hints:

Thinner: Bare Wood - Special Thinner 216.
Thinning: Spray - Special Thinner 216.

Cleaner: Bare Fiberglass - Fiberglass Solvent Wash 202. Bare Wood - Special Thinner 216.
Airless Spray: Pressure: 170-204 bar/2500-3000 psi. Tip Size: 0.53 mm/21 thou.
Conventional Spray: Pressure Pot: Pressure: 3.44-4.47 bar/50-65 psi (gun pressure); 10-15 psi (pot pressure). Tip Size: 1.8-2.2 mm/70-85 thou.
Other: Spraying of antifouling paints is prohibited in Canada. To prevent premature failure, ensure correct amount of paint is applied using the coverage as a guide.

Some Important Points: Product temperature should be minimum 10°C/50°F and maximum 29°C/85°F. Ambient temperature should be minimum 10° C/50°F and maximum 35°C/95°F. Substrate temperature should be minimum 10°C/50°F and maximum 29°C/85°F.
Compatibility/Substrates: Apply to clean, dry, properly prepared surfaces only. Surface must be dry and clean, and free from grease, detaching paint etc. Do not apply Trilux 33* directly to aluminum. All metal surfaces must be primed with Interprotect 2000E/2001E or Primocon. Do not apply to tin-based paint such as Micron® 33, 44 or Tri-Lux® IIT.
Number of Coats: 2; Bare Wood: 3 coats (first thinned)
Coverage (Theoretical) - 443.7 ft²/gal by brush
Recommended DFT: 2 mils dry
Recommended WFT: 3.6 mils wet
Application Methods: Airless Spray, Brush, Conventional Spray, Roller(Pressure Pot) . Spray application is recommended only for Professional Applicators that have all the proper safety equipment including a full-face shield.