Tag Archives: Awlgrip HDT Application Guide

How to Apply Awlgrip HDT

Surface Preparation

The surface preparation advice provided, and equipment suggestions, can be used as a guide. Preparation techniques and results will vary according to individual conditions, equipment choice/condition and other factors. Testing on a non-critical area should be carried out prior to full-scale preparation.
Awlgrip HDT should be applied over Awlgrip 545 Epoxy Primer or previous Awlgrip Topcoat/Awlgrip HDT/Awlcraft 2000.
Over Awlgrip Topcoat/Awlgrip HDT/Awlcraft 2000 topcoat sand topcoat with P400 to remove the gloss and clean with surface cleaner T0170 (US) or T0340 (EU) using the two cloth wipe down method.
Avoid painting in direct sunlight. Do not apply paint materials to surfaces less than 5°F (3°C) above dew point, or to surfaces warmer than 105°F (41°C).
Ambient temperature should be minimum 55°F (13°C) and maximum 105°F (41°C). At standard conditions (77˚F (25˚C), 50% R.H.), avoid applying topcoats when the temperature could drop below the dew point within 6–8 hours after the application.

Mixing & Reduction of Awlgrip HDT
Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application of a small sample before full-scale application is recommended.
Mix Ratio (by volume) – 1:1:0.25 (Base : Curing Solution : Activator)  (eg 1 Gallon:1 Gallon:1 Quart or 100:100:25ml).
Induction time = 15 minutes.
Mix to a smooth, homogenous mixture
Awlgrip HDT is designed for spray application only. Correct choice of activator must be made according to the application conditions and project size.
General guideline:
15-23ºC OA0020
20-30 ºC OA0015 (US only)
>30ºC OA0010

1. Mix all 3 components of Awlgrip HDT thoroughly, especially the base. Mix by volume to a homogeneous mixture:

For example, mix 100ml OC series, 100ml OC0010 & 25ml OA0020 (or 32 ounces OC series, 32 ounces OC0010 & 8 ounces OA0020). Keeo in mind that adding more activator into the mix may compromise pot life and could affect the flow of the product.
2. Once the product is mixed, ensure at least 15 minutes induction time. If the induction time is not followed, the product may down gloss / haze once cured.
3. Initial spray viscosity should be 14-20 seconds (DIN4 or equivalent) and varies with the application conditions. The best choice of activator will depend on application conditions and boat size.

As a general guideline (see below):

Application & Conditions for Awlgrip HDT

4. Application equipment: Gravity or pressure feed, air atomized spray or electrostatic spray
5. The primed surface must be clean and dry.
6. Apply 2 coats of Awlgrip HDT, this should be sufficient to achieve the correct DFT of 50-75 microns (3mils) DFT. However, some colours may require additional coats to achieve full hide / opacity and colour development. Application of the first coat should be approximately 75 microns (3 mils) WFT and application of the second coat should be approximately 100 microns (3.9mils) WFT. The surface may not become completely ‘tack free’ in between coats, however it is recommended to wait at least 30 minutes between coats (this time will vary depending on activator selection, temperature and humidity and air flow)
7. Awlgrip HDT has a relatively short pot life compared to Awlgrip topcoat, so for optimal performance prepare a fresh mix for each application. Don’t mix the new & old paint together as this may compromise the final finish.
8. The Awlgrip HDT activators can be blended together to suit not only environmental conditions but also project complexity. For a good starting point use a 50/50 OA0010/ OA0020 blend (or OA0015) then adjust to your preference.
8.1 To achieve a longer pot life or longer wet edge, the blend of A0010 and A0020 should be adjusted to include more A0010.
8.2 Similarly, for small areas or where drying time needs to be reduced, the proportion of A0020 should be increased.

9. Even if temperature has a greater effect on the cure and the potlife, humidity to some extend can also have an influence on the flow and performance of the product.
9.1 In cooler humid conditions it is suggested to either use only OA0020 or a blend of OA0020 and OA0010 with a higher proportion of OA0020 to OA0010. Example 75/25 OA0020/OA0010.
9.2 In hot humid conditions it may be necessary to increase the proportion of OA0010 and decrease the proportion of OA0020. Example, 75/25 OA0010/OA0020. Even in hot humid conditions, it is not recommended to solely use OA0010 due to the risk of moisture causing down glossing.
10. When first using Awlgrip HDT, it can apply differently to other topcoats currently in use. To help with this, up to 12.5% of T0002, T0001, T0003, T0005 or T0031 can be added to help with wetting out of the surface. Using extra reducer may require an additional coat to be applied and will mean the product is no longer ‘VOC compliant’. Once applicators are used to the behaviour of HDT on application, a similar quality of finish can be achieved without the addition of extra reducer. It is recommended to mix separately the Activator (OA0010, OA0015, OA0020) in equal amounts to the chosen reducer. This mix can then be added to the 1:1 base & curing solution at 25%. This mix will contain 12.5% Activator (as recommended) with 12.5% reducer; from a painters perspective this gives a 1:1:0.5 overall mix ratio.
11. Thanks to the activator/ reducer choice based on temperature, Awlgrip HDT has been proven to be a very adaptable product. The chart on page 1 is to be used as a guide only. In low temperatures, the standard paint mix with fast activator works very well. On larger surfaces, the addition of standard solvents helps to carry a wet edge if the applicator is struggling. For hot weather, OA0015 activator works well. If the applicator is struggling with wet edge, the addition of solvents helps. It is recommended when blending the activators to use the two extremes OA0010 Slow) and OA0020 (Fast) this allows more control. In low temperatures, we recommend T0001 or T0002; in medium temperatures T0003 and in hot temperatures T0005. In hot to very hot weather T0031. Start with the addition of 5% solvent. It is recommended for larger applications that a pre-shoot on panels is to be carried out, “to enable applicator to choose” the best optimization for the size project and conditions.
DRYING TIMES & REPAIRS for Awlgrip HDT
12. If environmental conditions require that the product dries faster (cooler more humid conditions), add slightly more OA0020 into the mix. Keep in mind this may compromise pot life and could affect the flow of the product. Also, in that case the product is no longer VOC compliant.
13. Awlgrip HDT has a new repair process compared to the standard Awlgrip repair. See the Repair & maintenance brochure for further info.
14. Awlgrip HDT can be harder to polish therefore we only recommend this for repairs and to remove localised defects. If working in an environment where you know you’re going to polish the whole boat, Awlcraft 2000 is the best choice.
15. Polishing Awlgrip HDT : Always test a small, low visibility area (or a sample panel) first before proceeding. Certain color shades may not be suitable for polishing. The tone of the color may be affected during sanding or aggressive polishing. Multi-stage sanding & polishing systems can also be used. You should contact your local supplier for further information.

Awlgrip HDT Application continued

Application equipment and parameters are given as a guide. Actual equipment choices will vary according to application conditions, equipment condition and other factors. Testing on a non-critical area should be carried out prior to full-scale application. Contact your local technical service representative for further advice if necessary.
To ensure optimal adhesion between coats Awlgrip HDT should be applied according to the overcoating intervals as described in the Recoatability & Drying Times section.
Apply a full coat of Awlgrip HDT to the surface. Allow tack coat to “flash off” 30-45 minutes depending on application conditions. Apply a slightly heavy second coat. A third coat can be applied to reach DFT if needed.                         

Application MethodsFluid TipFluid PressureAir Pressure
Conventional Spray Gravity,
Electrostatic
1.20 – 1.40 mm
47 – 55 thou
 –180 – 280 cc/min3 – 5 bar
29 – 44 psi

Recoatability & Drying Times
The data given for recoatability is not exhaustive. Actual recoatability can vary according to individual conditions, climate and surroundings. If unsure, consult your local technical service representative before proceeding.

Drying15ºC (59ºF)25ºC (77ºF)35ºC (95ºF)
Hard Dry46 hours22 hours6.5 hours
Touch Dry6 hours4.5 hours1.5 hours
Pot Life3 hours2/5 hours2 hours

Values in the table are for a 50:50 mix by volume of Awlgrip HDT Fast Activator and Awlgrip HDT Slow Activator. If using only Awlgrip HDT Fast Activator or Awlgrip HDT Slow Activator at a different ratio drying time and pot life will vary.

Awlgrip HDT has a shorter pot life than a standard polyurethane topcoat.

Overcoated by15ºC (59ºF)15ºC (59ºF)25ºC (77ºF)25ºC (77ºF)35ºC (95ºF)35ºC (95ºF)
MinMaxMinMaxMinMax
Awlgrip HDT2 hours24 hours2 hours24 hours2 hours24 hours

Recoatability: Spray application consists of 2 to 3 coats applied over 2-4 hours. Exact time will vary with temperature, project size and film thickness applied. Awlgrip HDT cannot be overcoated with itself after 24h. Please contact your local representative for more information
Some Important Points
Awlgrip HDT is compatible with Awlgrip repair product. Please refer to the Awlgrip website or to the Awlgrip Application Guide for further information.

Awlgrip Product Data Sheet

TIPS & TRICKS FOR AWLGRIP HDT APPLICATION